¶ Introduction
The LDT-RX1 is a wireless receiver unit that is designed to receive data from the wireless LDT range. A powerful receiver module that works at sub Wi-Fi frequency which will cut through the wireless noise of a busy set to deliver excellent results when paired with an LDT wireless transmitter product.
Please note that one LDT-RX1 is required for each LDT wireless transmitter.
¶ LDT-RX1 Compatibility
- LDT-V2 (Manual here)
- LDT-TX1 (coming soon)
¶ LDT-RX1 Components
| 1 | PWR Port | 2 Pin Lemo | 5 | LED | LED Status 3 (on back) |
| 2 | ETH Port | RJ45 | 6 | RF | Antenna Port |
| 3 | LED | LED Status 1 | 7 | Reset | Reset Button |
| 4 | LED | LED Status 2 | 8 | Threads | Rigging Threads |
¶ LED Status
| Led Status 1 | Green The unit has power. Red Unit is powered by PoE. |
| Led Status 2 | Flashing Green Ready. |
| Led Status 3 | Green RF is connected. Red RF not connected. |
| ETH Port | Yellow PoE is good. Green Ethernet is connected. |
¶ Physical Connection
| Name | Type | Description | Cable Codes |
|---|---|---|---|
| PWR | 2pin 0B Lemo | Power for the LDT-RX1 | PWRE |
| ETH | RJ45 | Ethernet connection port | Ethernet cable |
¶ Cable Types and Codes
All DCS cables are categorized using a code and a bend relief color for each of the cable types. The lemo connector type can be straight (S), right angle (R), or anglissimo (O). Custom cables can be made upon request.
| Code | Bend Relief Color | Type | Description |
|---|---|---|---|
| PWRE | White | 2 pin Lemo to international socket | Used to power the LDT-RX1 from a mains supply |
| Not DCS specific cable | N/A | Ethernet to ethernet | Used to send data to the media player machine. Use any compatible RJ45 ethernet cable |
¶ Status Lights
The LDT-RX1 has 3 status lights on the unit and 2 status light on the ethernet port to provide an overview of how the unit is working.
¶ LED below PWR:
- Green: External power in
- Red: Power failure
¶ LED in between PWR and ETH:
- Heartbeat light means there is connection between the OEM and the LDT-RX1 motherboard
¶ LED on the ETH port :
- Green: Solid - when connected. Blinking - data is being sent.
- Yellow: Solid - PoE is connected and valid
¶ LED below antenna:
- Green: Connection to LDT Transmitter
- Red: No connection
¶ Reset Button
The recessed reset button is to be used to manually reset all the settings of the LDT-RX1.
The reset will occur after the button has been pressed for 2 seconds.
The unit will reboot shortly after this. The status LED/heartbeat will turn orange when the reset is pressed successfully.
Please note that all settings will revert to factory default and any personalised settings will be lost.
¶ Mounting
The LDT-RX1 casing has 3 points to mount the unit to a 3/8" stand.
¶ Antenna
The LDT-RX1 is compatible with any SMA male antenna which works between 2200-2500 MHz freq.
¶ Frequency information
The LDT-RX1 works at any frequency between 2200mhz and 2500mhz. This is configurable in the settings.
Please note that the DCS wireless system only works between DCS branded products and requires an LDT transmitter and receiver. For instance an LDT transmitting device (such as the LDT-V2) cannot be connected to a 3rd party router or other receiver and must be paired with a LDT reciever (such as the LDT-RX1).
If you are experiencing any level of interference with the wireless settings then fine tuning the settings of the LDT-RX1 and other wireless device will provide a more robust connection.
If any wireless settings are changed on the LDT-RX1 then please ensure that the same settings are set-up on the corresponding LDT transmitting device. LDT-V2 settings can be found here.
¶ Connection Information
Regarding issues with connecting the LDT-V2/LDT-RX1 to network equipment:
The DCS devices auto negotiate on Ethernet upto a rate of 100Mbps. The network equipment must be able to negotiate down to this rate. Equipment limited to 10G/1Gbps may require additional interfacing.
¶ Settings
The LDT-RX1 settings are controlled by a built in web interface.
¶ Accessing the LDT-RX1 Settings
- Connect to a computer using an ethernet cable connected to the ETH port and the corresponding port of the computer,
- Power the LDT-RX1 using the PWRE cable,
- Change the IP address of the computer to 192.168.1.XXX,
- On a web browser type in 192.168.1.100.
This will connect you to the web browser where all settings can be adjusted.
Browser options bar
¶ Status
An overview of the wireless connection.
Optimal levels would be:
- RX level: -40db
- SnR: 10db
- Packet Loss: 0%
System Uptime - How long unit has been powered up for this session.
¶ Radio
Frequency can be changed here. If value is changed here then please update the settings of the corresponding LDT wireless transmitter.
The default value of the LDT-V2 is 2405mhz. Go here to see how to change the wireless settings on the LDT-V2.
¶ Destination
IP address and port of the destination machine.
¶ Unit
Network settings of the LDT-RX1 unit. Change these according to network settings.
¶ Info
Specific information about the hardware of the LDT-RX1 unit.
¶ Firmware
All LDTs are shipped with the latest firmware. However DCS are constantly refining and adding features. Please send an email to support@dcs.film requesting your email address to be added to the firmware mailing list to be kept up-to-date.
To update the firmware download it to your machine. Choose the relevant file and the web browser will upload it to the LDT-RX1. Screen will say "Uploading firmware" than it will reboot if the upload was successful.
¶ Further Support
For any additional support or questions please contact DCS: support@dcs.film