- Select Lens (only when Auto Lens Select is off)
- DCS Zoom test: 11-110mm (1)
- Calibrate LDT-E
- Settings
- Camera index (only in SD mode)
- A-Z
- Roll (only in SD mode)
- 001-999
- Project FPS (only in SD mode)
- 23.98
- 24 (default)
- 25
- 29.97
- 30
- Auto lens select (this tells the LDT what lens is loaded from the Preston)
- Off (default) (use this if the focus puller is not using F-Mapping)
- On (use this if the focus puller is using F-Mapping)
- Circle of conf. (only used for calculating the Depth of Field)
- 0.013 (default)
- 0.015
- 0.02
- 0.025
- 0.03
- 0.035
- 0.04
- 0.045
- 0.05
- File format (only in SD mode)
- CSV - ASCII (default)
- DCS - Binary
- Cam family
- ARRICAM
- ARRIFLEX
- Panavision XL2
- Dumb
- SERIAL Port
- MDR LOOP (default)
- DCS IN/OUT
- DCS IN
- Network
- DCS streaming
- Service
- On
- Off (default)
- Multicast
- On
- Off (default)
- Remote IP
- User Defined (default 192.168.1.200)
- Remote port
- User defined (default 33322)
- Local IP
- User Defined (default 192.168.1.100)
- Router IP
- User Defined (default 192.168.1.1)
- Netmask
- User Defined (default 255.255.255.0)
- Advanced
- Data Source
- Local table (default) (for normal operation)
- Pull from Remote (special operation only. Only choose this option if instructed to do so by a member of the DCS team)
- Pull from Lens (take lens data from smart lens)
- Pull from LCUBE
- Pull from Nucleus-M
- Pull from Camin
- Lens Database
- List (default)
- Folders
- Flip GUI
- Auto (default)
- No
- Yes
- Format SD Card
- Factory Defaults
- DCS Protocol
- RAW Encoder
- Disable
- Enable (default)
- Tilt/Roll
- Disable
- Enable (default)
- Load Config
- Motor/LDE setup
- Focus
- Normal (default)
- Reverse
- MDR F (default)
- MDR I
- MDR Z
- MDR AUX
- Iris
- Normal (default)
- Reverse
- MDR F
- MDR I (default)
- MDR Z
- MDR AUX
- Zoom
- Normal (default)
- Reverse
- MDR F
- MDR I
- MDR Z (default)
- MDR AUX
- Desqueeze
- Anamorphic Desqueeze
- On (default)
- Off
- Overlay (The following settings are on the overlay output)
- Frame lines
- 1
- Enabled
- On
- Off
- Aspect Ratio
- 1.33:1
- 1.66:1
- 1.78:1
- 1.85:1
- 2:1
- 2.39:1
- User
- Upper Left (Only if Aspect Ratio is set to User)
- Lower Right(Only if Aspect Ratio is set to User)
- Scale (Only if Aspect Ratio is active)
- Set Scale 0-100% (default is 80%)
- Offset (Only if Aspect Ratio is active)
- Set Position X & Y
- 2
- Enabled
- On
- Off
- Aspect Ratio
- 1.33:1
- 1.66:1
- 1.78:1
- 1.85:1
- 2:1
- 2.39:1
- User
- Upper Left (Only if Aspect Ratio is set to User)
- Lower Right(Only if Aspect Ratio is set to User)
- Scale (Only if Aspect Ratio is active)
- Set Scale 0-100% (default is 80%)
- Offset (Only if Aspect Ratio is active)
- Set Position X & Y
- 3
- Enabled
- On
- Off
- Aspect Ratio
- 1.33:1
- 1.66:1
- 1.78:1
- 1.85:1
- 2:1
- 2.39:1
- User
- Upper Left (Only if Aspect Ratio is set to User)
- Lower Right(Only if Aspect Ratio is set to User)
- Scale (Only if Aspect Ratio is active)
- Set Scale 0-100% (default is 80%)
- Offset (Only if Aspect Ratio is active)
- Set Position X & Y
- Colour
- White
- Yellow
- Red
- Green
- Blue
- Purple
- Orange
- Cyan
- Black
- Line Width
- Fine
- Medium
- Thick
- Shading
- 0%
- 10%
- 20%
- 30%
- 40%
- 50%
- 60%
- 70%
- 80%
- 90%
- 100%
- Desqueeze
- Set by lens (x.xx)
- 1.0 (off)
- 1.25
- 1.3
- 1.5
- 1.65
- 1.8
- 2.0
- Custom (XXX)
- Custom Desqueeze 1.0 - 2.0
- Overlay background
- Shrink video to fit
- Black
- 90% opaque
- 80% opaque
- 70% opaque
- 60% opaque
- 50% opaque
- 40% opaque
- 30% opaque
- 20% opaque
- 10% opaque
- Transparent
- Overlay brightness
- Max
- 9
- 8
- 7
- 6
- 5
- 4
- 3
- 2
- Min
- Overlay Items
- Lens
- Focal Length
- Iris
- DoF
- Focus
- Clip
- Footage
- Tilt/Roll
- REC
- Shutter
- FPS
- Timecode
- Add Lens
- Edit Lens
- Delete Lens
- Save Config
- Browse clips
- Info